Product Search
Search results for 'D-560'
Showing 61 - 81 of 563 Total Results
CA-2170
Location: 30 Minute Timer
Plug aggregate equipment into the outlet at the back of the timer. Then plug timer cord into a wall outlet and turn the knob to the desired time. Time switch will turn off equipment automatically when time expires.
Location: Soils
Test Mark's COE Manual Compaction Hammer features a recoil mechanism in the foot assembly to reduce impact fatigue.
SA-2000
Location: CBR Load Frames
The CBR (California Bearing Ratio) loading press from Test Mark uses a two-position mechanical jack to provide steady test speeds, as well as rapid travel of the platen for positioning of the sample.
CA-0370
Location: Slump Testing
This cast-aluminum base provides a sturdy, level surface on which to perform slump tests. Cleats dig into the ground for firm, level support.
Cylinder Platen, 6 ½” Diameter
(3) options
Location: Test Platens
Free floating bearing platen seats under test pressure. . Used when testing 6” (152 mm) or 4” (101 mm) diameter concrete cylinders in compression. Platen is manufactured from steel with all components plated for corrosion resistance. Upper cylinder platen used when testing 6” (152 mm) or 4” (101...
CA-0470
Location: Rubber Mallet
The rubber mallet from Test Mark is used to consolidate materials and release entrapped air in concrete molds, air meters, slump cones and unit weight buckets.
SA-2019
Location: CBR Accessories
100 pack of coarse grade paper filter, used to separate spacer disc and soil in the CBR mold during compaction operation or over the top surface of the soil when the compaction operation is completed.
CA-0710
Location: Chase Air
The Chase Air Kit from Test Mark provides an economical method of quickly estimating the air content of fresh concrete in the field using the isopropyl alcohol method.
Digital Static Cone Penetrometer
SA-1510
Location: Static Cone Penetrometer
Digital Static Cone Penetrometer from Test Mark features a large digital readout making testing and recording readings easy.
CA-0610
Location: Air Entrainment/Roll-A-Meter
The lightweight aluminum Roll-A-Meter is used to determine the air content of concrete mixes, and is recommended for concrete containing lightweight aggregates, air-cooled slag or highly porous aggregates.
SA-3500
Location: Mud Balance
Mud Balances are used as standard procedure instruments for testing water and oil-base drilling fluids and oil well cements.
AA-0010
Location: Marshall Basic Compression Testing
The lower segment of Test Mark's Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
(3) options
Location: Aggregate Washers
Aggregate samples are automatically washed with Test Mark's aggregate washers to remove clay and other fines passing a No. 200 sieve.
CA-2080
Location: Sieve Storage Rack
This adjustable bench rack holds all diameters of sieves up to 12" (305mm) maximum. Stainless steel rack has non-skid rubber feet, and two permanent and two adjustable rubber-coated sieve support rods.
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
Screen Shaker Hydraulic Clamping
CA-2101
Location: Shakers
Test Mark provides screen shaker hydraulic clamping for aggregate testing applications. Easy online ordering.
CA-3000
Location: Flow Tables
Hand driven flow tables are used to determine consistency of cement mortars. A test specimen is molded on the table to a specified volume and shape.
Capping Compound *TEMPORARILY OUT OF STOCK*
CA-0100
Location: Capping Compound
Test Mark's Ultra-Strength Capping Compound is used to cap the ends of concrete test cylinders so compression force will be evenly distributed to the cylinder during testing.
AA-1000
Location: Reflux Extractor
The 1000g Reflux Extractor Set from Test Mark is used to determine the percentage of bitumen in a paving mixture using hot solvent extraction.
